Stock Ecotec Muffler Replacement
Stock Ecotec Muffler Replacement
I have the "300"hp Ecotec and have just replaced the exhaust pipe with the slippy pipe supplied by Brammo. I am not likely to invest in a completely new exhaust system anytime soon. My muffler is quite ineffective at reducing the noise level at anything other than steady throttle. Does anyone know of where to get a cost effective muffler that will bolt onto my pipe w/o modification?
I am looking to reduce noise level significantly without increasing backpressure to a level where it will reduce engine performance. I don't know if this is a pipe dream or is easily attainable. Can someone please advise me? Thanks.
I am looking to reduce noise level significantly without increasing backpressure to a level where it will reduce engine performance. I don't know if this is a pipe dream or is easily attainable. Can someone please advise me? Thanks.
Re: Stock Ecotec Muffler Replacement
Correct 2.5 inlet muffler... http://store.summitracing.com/partdetai ... toview=sku
Buy a 2.25" to 2.5" pipe adaptor (cut it shorter) and an extra pack of 12, 3" Supertrapp discs.(it only comes with 12)
Weld it to the end of the stock muffler outlet,right at the very end.Easily reversible with a Sawsall with minimal impact to the stock appearance.
You could clamp it on,but I wanted the most minimalistic approach.
89db@50' with 24 discs and NO backpressure(well, almost zero w/24 discs)
Buy a 2.25" to 2.5" pipe adaptor (cut it shorter) and an extra pack of 12, 3" Supertrapp discs.(it only comes with 12)
Weld it to the end of the stock muffler outlet,right at the very end.Easily reversible with a Sawsall with minimal impact to the stock appearance.
You could clamp it on,but I wanted the most minimalistic approach.
89db@50' with 24 discs and NO backpressure(well, almost zero w/24 discs)
Last edited by MadMaxedAtom on Sat Dec 29, 2007 6:12 pm, edited 1 time in total.
Re: Stock Ecotec Muffler Replacement
Thank you for that idea MadMax! What is the db rating of the stock fart can?
Re: Stock Ecotec Muffler Replacement
101db @ 50'! I was told not to return till I did something about it.
So,being a cheap SOB,I started to dig.... and came up with a perfect solution that installed in about 1hr. with no loss of power.
I did not want to invest in a new exhaust I would have to discard during turbo installation in the future ;
So,being a cheap SOB,I started to dig.... and came up with a perfect solution that installed in about 1hr. with no loss of power.
I did not want to invest in a new exhaust I would have to discard during turbo installation in the future ;
Last edited by MadMaxedAtom on Sat Dec 29, 2007 4:10 pm, edited 1 time in total.
Re: Stock Ecotec Muffler Replacement
So, what kind of investment does it require? Oops, just have to look at the website.
Re: Stock Ecotec Muffler Replacement
2.25 to 2.5 " exhaust pipe adaptor... $17 bucks (usually cheaper locally)
Muffler is $72 bucks http://store.summitracing.com/partdetai ... toview=sku
and extra discs are $27 bucks....
http://store.summitracing.com/partdetai ... P-504-6512
Total cost about $120/shipped.
Very simple to weld it on the end of the tp,or clamp it, Jed!
In all honesty,I swear my car is faster.Might just be it's SO much quieter it surprises you a bit more
Muffler is $72 bucks http://store.summitracing.com/partdetai ... toview=sku
and extra discs are $27 bucks....
http://store.summitracing.com/partdetai ... P-504-6512
Total cost about $120/shipped.
Very simple to weld it on the end of the tp,or clamp it, Jed!
In all honesty,I swear my car is faster.Might just be it's SO much quieter it surprises you a bit more
Last edited by MadMaxedAtom on Sat Dec 29, 2007 6:13 pm, edited 1 time in total.
Re: Stock Ecotec Muffler Replacement
I assume the adaptor is necessary to go from the stock exhaust diameter to that of the Supertrapp inlet? Also, I would assume that they make only one diameter? Or shall I say that they don't make a diameter to exactly fit our stock muffler pipe.
Last edited by rfmarz@frontiernet on Sat Dec 29, 2007 4:30 pm, edited 1 time in total.
Re: Stock Ecotec Muffler Replacement
MY BAD! It's been a while since I did this.You will need this muffler; http://store.summitracing.com/partdetai ... toview=sku
which has a 2.5" inlet.Our stock tailpipe outlet is 2.25",so you will need a 2.5" to 2.25" adaptor..
which has a 2.5" inlet.Our stock tailpipe outlet is 2.25",so you will need a 2.5" to 2.25" adaptor..
Re: Stock Ecotec Muffler Replacement
Thanks for the info MadMax. I just ordered one+adapter and will either weld it myself or take it down to the local muffler shop. I also recommended this to one of my friends who has a shannon race car since he is running straight pipe and had been looking at some sort of easy muffler/silencer solution.
I have never welded anything before, is it a pretty straightforward process? I wanted to learn how to do it. I noticed my adapter is aluminized finish but steel and the muffler is steel, so is that considered a straight steel-steel weld? Btw, there are adapters for $5.99 at summit:
http://store.summitracing.com/partdetail.asp?autofilter=1&part=WLK%2D41961&N=700+4294923429+4294820497+4294846842+115&autoview=sku
Any welding pointers would be appreciated. One of my friends has a lincoln set I can borrow where the wire is fed out automatically.
-Brad
I have never welded anything before, is it a pretty straightforward process? I wanted to learn how to do it. I noticed my adapter is aluminized finish but steel and the muffler is steel, so is that considered a straight steel-steel weld? Btw, there are adapters for $5.99 at summit:
http://store.summitracing.com/partdetail.asp?autofilter=1&part=WLK%2D41961&N=700+4294923429+4294820497+4294846842+115&autoview=sku
Any welding pointers would be appreciated. One of my friends has a lincoln set I can borrow where the wire is fed out automatically.
-Brad
Re: Stock Ecotec Muffler Replacement
yeah....where a welding mask haha good luck Brad!!! hopefully someday I'll have my car back with a new exhaust to show off to everybody!
Re: Stock Ecotec Muffler Replacement
Brad,welding with a MIG wire feed welder is almost as easy as drawing a line with a pen.
The alu finish will not bother the welding process. (galvinized coatings do,but we won't discuss that.. )
Practice a little bit on the same thickness material you will be welding to find the ideal heat range and wire feed speed.
The arc should be consistent and sound like bacon frying when you are doing it correctly.
Watch the puddle and not the arc.The puddle is where it all happens.
It really is very easy.
The most difficult jobs encountered welding require you to fill gaps or weld dissimilar or dirty materials.
Once you run a bead or two,you will be hooked
You can start with a .024 wire,115v wire feed mig welder (around $450) with gas shield and unless you start to get into thick stuff will never need a bigger machine.
Flux core mig is OK,but not as clean as gas shield mig.
Gas shielded mig requires you buy/rent a gas cyl, but it is worth it.
CO2 gas will be fine unless you plan on welding alu or stainless. I use Argoshield,which is a mix of Argon and CO2.
I use a 115v .024 wire size MIG for lightweight welding and a 220v .030 wire MIG for more serious stuff.
Next thing you will want is a plasma cutter
The alu finish will not bother the welding process. (galvinized coatings do,but we won't discuss that.. )
Practice a little bit on the same thickness material you will be welding to find the ideal heat range and wire feed speed.
The arc should be consistent and sound like bacon frying when you are doing it correctly.
Watch the puddle and not the arc.The puddle is where it all happens.
It really is very easy.
The most difficult jobs encountered welding require you to fill gaps or weld dissimilar or dirty materials.
Once you run a bead or two,you will be hooked
You can start with a .024 wire,115v wire feed mig welder (around $450) with gas shield and unless you start to get into thick stuff will never need a bigger machine.
Flux core mig is OK,but not as clean as gas shield mig.
Gas shielded mig requires you buy/rent a gas cyl, but it is worth it.
CO2 gas will be fine unless you plan on welding alu or stainless. I use Argoshield,which is a mix of Argon and CO2.
I use a 115v .024 wire size MIG for lightweight welding and a 220v .030 wire MIG for more serious stuff.
Next thing you will want is a plasma cutter
Re: Stock Ecotec Muffler Replacement
Mad, I just got my pancake muffler from Summit. Since this is a muffler by itself, what do you think of getting a short piece to bolt onto the pipe before the existing muffler, then removing the muffler and replace it with the pancake?
Re: Stock Ecotec Muffler Replacement
Interesting,but I think it's going to be too loud.
Then again,with 12 discs,it may be OK.
You may have to....experiment. hehehe...
Then again,with 12 discs,it may be OK.
You may have to....experiment. hehehe...
Who is online
Users browsing this forum: No registered users and 2 guests